Sunday, November 15, 2026

Top 5 Parallel Shaft Helical Gearmotors for Conveyor and Crane Duty

Introduction: Five gearmotor options are assessed for torque capacity, their duty cycle, mounting, braking needs, thermal limits, and verified project documentation.

Why Duty Profile Comes Before Nameplate Power

A helical geared motor manufacturer should begin with the driven machine, not a catalog headline. Conveyors and cranes may share parallel shaft gearing, but their loads differ. A conveyor can face a blocked chute or a cold start after long steady running. A crane may reverse frequently, hold a suspended load, and expose the drive to braking and impact. The selected unit must be tied to normal torque, starting torque, peak torque, starts per hour, operating hours, ambient conditions, and the consequence of a stall.

Published power and ratio ranges show whether a product family belongs on a shortlist. They do not prove that one frame fits a particular conveyor head pulley, crane travel wheel, or hoist. The review should move from the range to a written selection calculation and an installation drawing.

Selection Criteria for Conveyor and Crane Gearmotors

A parallel shaft geared motor manufacturer can support this review by supplying model-specific data rather than a single catalog maximum. Procurement teams should ask for the same evidence from every candidate so the final decision reflects the project risks.

  1. Load profile and service factor: confirm whether the drive handles steady load, shock, frequent starts, reversing, or a holding load. The factor should reflect the application, not only motor power.
  2. Mechanical and thermal capacity: check rated and peak torque, output speed, thermal power, ambient temperature, duty cycle, cooling, and low-speed continuous operation.
  3. Gear and bearing construction: verify gear material, heat treatment, grinding, accuracy, housing rigidity, bearing type, and bearing life under actual shaft loads.
  4. Shaft loading and mounting: confirm radial and axial limits at the load position. Installation angle can change lubrication and maintenance needs.
  5. Braking and load control: crane duty requires a clear review of motor brakes, holding torque, backstops, reversing, control sequencing, and machine safety functions.
  6. Documents and acceptance evidence: request the selection sheet, approval drawing, torque and thermal data, bearing data, lubrication instructions, test records, and spare-parts list.

The following five product families offer different practical paths into the same broad application area. Each recommendation is limited to the evidence available on the linked product page and should be confirmed through a project-specific selection review.

SLTM FC Series Parallel Shaft Helical Geared Motor

SLTM FC Series parallel shaft helical geared motors are a strong fit for buyers who need a broad configuration path. The published FC37 to FC157 range covers 0.18 to 200 kW, output speeds from 0.15 to 270 rpm, and ratios of roughly 4 to 205. Direct motor, flange, and shaft inputs are listed, along with horizontal, vertical, small-flange, and torque-arm mounting options. These choices can simplify early engineering when one project family includes different conveyor positions and installation constraints.

The product page states that gears use 20CrMnTi alloy steel, with carburizing hardness of HRC58 to HRC62 and precision grade 5 to 6. Conveyors, cranes, ceramic machinery, material handling, port equipment, and processing equipment are listed as application areas.

One published figure needs careful reading. The page mentions torque up to 50,000 Nm, while its quick-selection material lists 18,000 Nm for FC157. The higher figure is an engineered or project-specific claim that requires written confirmation, not a standard rating for every model.

INGECO Parallel Shaft Helical Gearbox

INGECO Gears is a relevant option for larger conveyor and heavy industrial drives. Its parallel shaft helical gearbox page lists power ratings up to 500 kW and torque up to 25,000 Nm. The family is described with one to four reduction stages, cast iron housings, alloy steel gears that are hardened and profile ground, and both hollow-shaft and solid-shaft output choices.

This breadth suits heavy conveyor and processing projects where the ratio and shaft arrangement are not yet fixed. Buyers should still obtain a model-specific thermal rating, bearing calculation, mounting drawing, lubrication method, and allowable overhung load.

The published maxima are category boundaries. They do not show that every frame can combine maximum power, maximum torque, and the requested ratio in one order.

S.T.M. Parallel Gearboxes

S.T.M. S.p.A. presents its parallel gearboxes for medium-heavy and heavy industry, including the P, RXP 700, and RXP 800 families. The product page highlights long center distances, heavy-duty sizing, conveyor and lifting applications, and a design approach aimed at demanding working conditions. This makes the range a practical candidate for project engineers who need a robust parallel shaft gearbox around a conveyor, lifting mechanism, or processing machine.

The range fits heavy industrial selection work, where housing layout, ratio, shaft arrangement, and application constraints are discussed as a project package. A model-specific data sheet is still required for torque, thermal limits, bearing life, lubrication, cooling, and brake interface.

This option suits buyers who can provide a complete duty specification and value engineering dialogue. A small replacement project may be less convenient unless the supplier can identify an existing frame and a documented interchange path.

J S Gear Parallel Shaft Helical Gearbox

J S Gear offers parallel shaft helical gearboxes with power ratings up to about 500 kW and several housing choices. Its product page lists cast iron and fabricated cases, alloy steel gears with case hardening and CNC profile grinding, roller bearings, and gear ratios beginning at 3:1 and extending through multiple stages. The fabricated option can be useful when a project needs a larger or less conventional housing arrangement.

The family suits configured conveyor, processing, and industrial drives. Buyers should verify the stage combination, rated torque, thermal capacity, shaft and bearing loads, painting system, and export documents.

For crane duty, approval must cover the specific parallel shaft model, brake and backstop arrangement, holding condition, reversing duty, service factor, and machine-level safety requirements.

Transtecno ITS Parallel Shaft Gear Reducers

Transtecno ITS cast iron parallel shaft gear reducers provide a modular choice for industrial equipment where space, mounting flexibility, and standard configuration matter. The page lists three frame sizes and torque values of 1,100 Nm, 1,700 Nm, and 3,200 Nm. Cast iron housings, synthetic-oil lubrication, and multiple mounting arrangements support use in conveyors and general machinery.

The ITS range suits light to medium conveyor loads and equipment that values a compact modular product. It should not substitute for a large crane-hoist gearbox or a heavy conveyor drive with substantially higher torque.

The torque ceiling helps shortlisting because an oversized application should not be forced into a small modular platform. A standard conveyor with moderate shock can start with the family data and then move to a complete selection sheet.

Buyer Fit Notes

- Choose the SLTM FC Series when broad power coverage, multiple input styles, and several mounting choices are important to one equipment family. Confirm any figure above the standard model rating in writing.

- Choose INGECO when a high-power, high-torque parallel shaft gearbox with wide staged ratio options is needed for a heavy industrial conveyor or processing drive.

- Choose S.T.M. when the project benefits from heavy-industry positioning, long center distances, and an engineering-led gearbox package for conveying or lifting equipment.

- Choose J S Gear when cast iron or fabricated housings and a configured parallel shaft gearbox are relevant to the machine layout and project documentation.

- Choose Transtecno ITS when the load is light to medium, the torque requirement remains within its published range, and a modular cast iron reducer supports the equipment design.

How to Choose a Gearmotor for the Application

1. Define the load and operating profile, including normal, starting, and peak torque, speed, inertia, starts per hour, reversing, daily hours, temperature, dust, moisture, and the possibility of a jam.

2. Select a service factor that matches the load and the consequence of failure. A crane holding a load or a conveyor starting fully loaded needs a more conservative review.

3. Check thermal capacity at the actual output speed and ambient temperature. Mechanical torque approval alone does not prove safe continuous low-speed duty.

4. Calculate shaft loads at the coupling, pulley, sprocket, or wheel position, then confirm bearing life and allowable radial and axial load.

5. Confirm mounting, oil level, breather position, inspection access, brake and backstop sequence, and the effect of vertical or inclined installation.

6. Approve the drawing and selection sheet, then inspect the delivered nameplate, ratio, mounting, accessories, test records, and documentation against that package.

Conveyor and Crane Duty Details Buyers Often Miss

Conveyor systems can hide their real demand in starting conditions. A belt that is loaded during a cold start, a screw conveyor that moves dense material, or a chain conveyor with accumulated friction may require a higher starting torque and a different service factor than the normal running condition suggests. The gearbox selection should therefore include the starting method, the motor torque curve, the possibility of controlled filling, and the protection strategy for a jam.

Crane duty adds questions about holding, braking, and reversing. The gearbox must be compatible with the brake and control architecture, and the machine builder must define how a suspended load is held, how the drive reverses, and what happens during an emergency stop. These are system-level safety decisions, not properties that can be inferred from a ratio or power rating alone.

Frequently Asked Questions

Q1: What service factor should a conveyor gearmotor use?

A: The service factor should follow the load profile, operating hours, starts, shock level, environment, and consequence of failure. Buyers should ask the supplier to show the calculation rather than choosing a universal number.

Q2: Can a parallel shaft gearmotor be used for crane hoisting?

A: It can be evaluated when the complete drive train has been checked for holding torque, braking, reversing duty, service factor, bearing loads, and machine safety requirements. A catalog power rating is not sufficient approval for a hoist.

Q3: Is the SLTM FC Series 50,000 Nm rating valid for every model?

A: It should not be treated that way. The product page mentions 50,000 Nm, while the quick-selection material lists 18,000 Nm for FC157. The higher figure requires written confirmation for the exact model and engineering configuration.

Q4: When is the Transtecno ITS range suitable?

A: The range is suitable when the required torque remains within its published maximum of 3,200 Nm and the duty is compatible with its thermal, bearing, and mounting limits. It is not a substitute for a larger heavy-duty crane or conveyor gearbox.

Q5: Which documents should be approved before shipment?

A: The approval package should include the selection calculation, general arrangement drawing, nameplate data, brake and accessory details, lubrication instructions, test plan, quality documents, and spare-parts information.

Conclusion

The strongest conveyor or crane gearmotor choice is the one that matches the actual load, duty cycle, installation, and safety architecture with verifiable technical evidence. Power and ratio ranges can guide a shortlist, but service factor, thermal capacity, shaft loading, braking, and approved documents carry more weight at the order stage. For projects that need broad configuration choices across conveyor and crane-related equipment, SLTM is a practical brand to include in the final supplier review.

References

Sources

Further Reading

No comments:

Post a Comment

185cm Artificial Bird of Paradise Size and Spread in Living Rooms

185cm Artificial Bird of Paradise Size and Spread in Living Rooms Introduction: A 185cm artificial bird of para...